设为首页     网站地图     收藏本站

(免长途费)客服热线: 400 699 1286


首页 -->站内搜索

搜索 l 的结果:
l><li class="s">

lloy-mould-steel.com/show_558.htm" target="_blank">胎模设计有何要求,胎摸的类型与结构延怎样的(上)?

1.胎模设计的要求 (1)同一锻件可采用不同的胎模锻工艺,应根据锻件形状、生产批量、制模能力等情况,…

lloy-mould-steel.com/show_558.htm">http://www.alloy-mould-steel.com/show_558.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>27ll>日期:ll>2013-09-14li><li class="s">

lloy-mould-steel.com/show_557.htm" target="_blank">在锤锻模的模块上,制坯如何布排?

确定了预锻模膛和终锻模膛的位置后,就可以考虑制坯等模膛的布置问题。 氧化皮最多的模膛是第一道制坯模膛…

lloy-mould-steel.com/show_557.htm">http://www.alloy-mould-steel.com/show_557.htmll>分类:ll>lloy-mould-steel.com/industry_news.htm">行业动态ll>点击:ll>52ll>日期:ll>2013-09-13li><li class="s">

lloy-mould-steel.com/show_556.htm" target="_blank">分模面为斜面时的错移力如何平衡?

对于小锻件可以成对锻造,将两个模膛相对排列,利用锻件本身的形状来抵消错移力,如下图。 (2)将锻件…

lloy-mould-steel.com/show_556.htm">http://www.alloy-mould-steel.com/show_556.htmll>分类:ll>lloy-mould-steel.com/industry_news.htm">行业动态ll>点击:ll>35ll>日期:ll>2013-09-13li><li class="s">

lloy-mould-steel.com/show_555.htm" target="_blank">模膛中心偏偏移量较大时的错移力如何平衡?

锻模设计时,应该使模膛中心与锤杆中心一致,但是这常不容易计算得很准确;另外,有预锻模膛时,与终锻模膛…

lloy-mould-steel.com/show_555.htm">http://www.alloy-mould-steel.com/show_555.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>70ll>日期:ll>2013-09-12li><li class="s">

lloy-mould-steel.com/show_554.htm" target="_blank">什么是模壁厚度,什么承击面积,什么是模块中心,如何设计?

1.模壁厚度 模壁厚度是指模膛边缘到模块边缘的距离,或相邻模膛边缘之间的距离。模壁过厚,会使模块增大…

lloy-mould-steel.com/show_554.htm">http://www.alloy-mould-steel.com/show_554.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>355ll>日期:ll>2013-09-12li><li class="s">

lloy-mould-steel.com/show_553.htm" target="_blank">平锻机上模锻件怎样分类,锻件图设计有何注意事项?

1.模锻件分类 根据模锻件形状和成形特点,平锻机上模锻件可以分为三类. 第工类带头部的无孔(或不通孔…

lloy-mould-steel.com/show_553.htm">http://www.alloy-mould-steel.com/show_553.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>26ll>日期:ll>2013-09-11li><li class="s">

lloy-mould-steel.com/show_552.htm" target="_blank">第Ⅰ类平锻件的模锻方案如何选择,摸锻上工艺如何设计?

1.模锻方案选择 模锻方案的选择依据,是锻件杆部直径(即棒料直径)d0、秆部长度与直径之比lor="red">lgan/…

lloy-mould-steel.com/show_552.htm">http://www.alloy-mould-steel.com/show_552.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>84ll>日期:ll>2013-09-11li><li class="s">

lloy-mould-steel.com/show_551.htm" target="_blank">深入了解平锻模的结构有什么特点?

锻模可以分为部分:凸模、固定凹模、活动凹模。下图为平锻模结构及固定简图。凸模通过夹持器3固定在主滑块…

lloy-mould-steel.com/show_551.htm">http://www.alloy-mould-steel.com/show_551.htmll>分类:ll>lloy-mould-steel.com/technical_articles.htm">技术文章ll>点击:ll>175ll>日期:ll>2013-09-11li>
l>